JP's Gear Review v2.0 - Ep. 3.9 - Little Bear G3 "new" tube audio demo!

 


My dumb gym injury finally healed and I finally got around to make the audio demos with the "new" 6N2P-EV tube. It took a bit more time than I expected since I decided to be all fancy and properly edit it. My video edition skills are a bit rusty and Pinnacle Studio v24 was a pain in the rear-end and kept crashing on me for absolutely no reason, so the edits are simple and the overall quality is average at best. 

I recorded the videos in "Director View" mode. You'll see the amp and the pedal in full screen, and  my left side with the instrument inserted in the bottom right corner. Director View also limits the resolution to Full HD instead of 4K, so no super duper extra high definition this time.


Comments

Post a Comment

Popular posts from this blog

JP's Gear Review v2.0 - Ep. 3 - Little Bear G3: A tube-based overdrive for 65$! Is it any good?

Image
  Shortly after my latest purchases (that I still have to review), I fell into a Google Search rabbit hole of pedals that use a vacuum tube. The Blackbird, the AMT SS-20, the Ashdown Engineering Original Valve Pre-DI, and the Behringer VT999 were commonly discussed and I considered getting one of these, but quickly changed my mind. The first 3 are outrageously expensive (760$ for the Original Valve Pre-DI...) and the Behringer is difficult to find. The used ones go for roughly the same price as a new one, and it's not really worth it. However, another model showed up in the form of an eBay listing: Nobsound Little Bear G3 . It looks completely unassuming and very different than your typical pedal. It sells for about 65$CAD on eBay and has generally positive reviews. For the price, why not? I ordered it on the 23rd of August, and received it in my mailbox this afternoon. Unboxing Unboxing was uneventful. It was well packaged it lots of foam, and the tube was already installed. A 12V
Read more

STM32 Development: Configuring Arduino IDE/Visual Studio to build and deploy to STM32-based boards

Image
As a follow-up to my previous post, where I talked about using Visual Studio for Arduino development, this post will be providing an abridge guide to set it up correctly with Visual Micro's Arduino IDE for Visual Studio extension. There will also be a configuration guide to enable STM32 build and deployment. Prerequisites steps You NEED to have Arduino IDE (from arduino.cc) installed on your computer for full compatibility. The Windows Store App version is not supported by Visual Micro. Visual studio configuration Download Visual Studio Community Edition from Microsoft's website. https://visualstudio.microsoft.com/downloads/ Download Visual Micro's Arduino IDE for Visual Studio extension from either Visual Micro's website or Visual Studio Marketplace https://marketplace.visualstudio.com/items?itemName=VisualMicro.ArduinoIDEforVisualStudio https://www.visualmicro.com/page/Arduino-Visual-Studio-Downloads.aspx Launch the installer and follow the prompts. When asked which c
Read more

Overdrive, distortion, fuzz, hard clipping, soft clipping... What gives?

Image
 When talking about distortion, I often hear questions about what difference there is between an overdrive, a fuzz, and a distortion, and what's different between soft and hard clipping. I'll attempt to briefly answer those questions in the post.  What's clipping? "Clipping" is what happens to a signal when it is too powerful (or too hot) for a device. The type of clipping that is done depends on the circuit. In a effect pedal where an oversaturated signal is the intended end-result, makers will place certain diodes to clip the negative and positive parts of the waveform. The diodes don't have to be identical; you can use different diodes on both paths and-or combine many different diodes in series to shape the clipping to what you need. Designs using identical diodes are called symmetrical clipping circuits, and designs using different diodes are called (wait for it) asymmetrical clipping circuits. Reference signal The following graphs all use the following r
Read more